I. Introduction
The sub-terahertz (sub-THz) band (100–300 GHz) enables non-destructive, large-scale penetration imaging, making it highly attractive for real-time precision inspection and foreign body detection [
1,
2]. For such applications, detector pixels must provide high responsivity, compact footprint, and a simple interface to allow seamless integration into dense focal-plane arrays (FPAs) [
3]. Although various CMOS detector architectures have been investigated, many prior approaches face scalability challenges due to interconnections and bias pads, which often exceed the area of the active devices [
4,
5]. This motivates the need for detector topologies that minimize pad and bias overhead while maintaining high detection sensitivity.
In this letter, a CMOS detector IC is presented that eliminates external gate and drain biasing, thereby minimizing power consumption and achieving an ultra-compact active area. The design incorporates an on-chip balun and a differential concurrent-mode topology to enhance voltage responsivity (RV), followed by a high-gain amplifier chain for robust signal readout. Despite integrating these functional blocks, the detector occupies only 0.075 mm2 of the active area, underscoring its suitability for large-scale sub-THz imaging arrays. The proposed architecture represents a promising and power-efficient solution for next-generation industrial and security inspection systems.
II. Zero-Biased CMOS Detector
Fig. 1 shows the schematic of the proposed CMOS detector, including the integrated amplifier chain. Given that the cutoff frequency of the device technology exceeds the 120-GHz input signal, the detector operates in a transient regime under appropriate biasing. Under zero-gate-bias and floating-drain conditions, the incident sub-THz signal is rectified through the nonlinear and asymmetric capacitances among the gate, source, and drain. In conventional zero-bias CMOS detectors, however, the rectification relies solely on intrinsic device nonlinearity, leading to reduced sensitivity and narrow bandwidth. To overcome these circuit-level limitations, a concurrent-mode configuration is adopted by inserting an additional capacitance between the gate and drain, allowing the input signal to excite both nodes simultaneously and thereby enhancing the
RV [
6].
To further increase the
RV under zero-gate bias, impedance asymmetry between the source and drain is introduced by adding an inductor at the drain node. The optimal inductance, determined by the parasitic and cross-coupled capacitances, was analyzed using an ideal model, as shown in
Fig. 2(a). The analysis indicates a peak response near 120 GHz when the inductance is approximately 800 pH. However, this ideal case does not account for the effects of the self-resonant frequency (SRF) and the quality factor, and thus, cannot be directly applied to the practical design.
Fig. 2(a) should thus be interpreted as an indication that a higher inductance generally enhances the response, rather than as an achievable design target.
Fig. 2(b) presents EM simulation results of a realistically implemented transmission-line-based inductor, showing the trade-off between inductance and SRF. Although higher inductance is desirable, the SRF limitation prevents stable operation at 120 GHz when the inductance exceeds roughly 200 pH. Considering process and dielectric-constant variations of up to 20%, and ensuring robust operation beyond the SRF, an inductance of 189 pH was finally selected for implementation.
III. Measurement Results
Fig. 3 shows the chip photograph of the CMOS detector fabricated in a 40-nm CMOS process and its LTCC module for measurement. The active core area is 0.075 mm
2, while the total area including pads is 0.203 mm
2. Excluding the pads, the layout demonstrates that the balun for input matching, the added drain inductors, and the integrated amplifier chain can be compactly implemented within a very small footprint. The detector integrated in the LTCC module was characterized using a 120-GHz signal coupled through a simulated 1.6-dBi patch antenna, and the received signal was converted into a DC output. The incident power was normalized to the effective antenna aperture, and the output response was measured to extract the
RV and noise-equivalent power (NEP), as shown in
Fig. 4. Under zero bias, the detector with a 38-dB integrated amplifier achieved an
RV of 1,247 kV/W and an NEP of 1.6 pW/√Hz, whereas conventional CMOS plasmonic detectors typically exhibit peak
RV near the threshold bias. The peak
RV at zero bias indicates that detection is mainly governed by the MOSFET’s nonlinear capacitances, enhanced by the drain inductors, while the low NEP results from reduced power consumption that minimizes noise rather than from plasmonic excitation.
Table 1 provides a comparison of CMOS detectors operating in the sub-THz band [
4–
7]. The proposed detector achieves high
RV within a compact footprint and exceptionally low NEP, demonstrating suitability for low-power sub-THz sensing and confirming the viability of the architecture for scalable detector arrays. Although the referenced works operate at different frequency bands, this difference does not critically affect the fairness of comparison, since detector performance is more strongly determined by factors such as device process, circuit topology, and integration with on-chip amplifiers rather than by the operating frequency itself.
IV. Conclusion
The proposed CMOS detector IC incorporates drain inductors within a concurrent-mode structure, achieving enhanced RV and reduced NEP without external biasing. The NEP improvement stems from reduced power consumption, which suppresses noise contributions. With its compact and scalable design, the detector is well-suited for integration in large-scale sub-THz imaging arrays.
Notes
This work was supported by an ETRI grant funded by the ICT R&D program of MSIT/IITP (RS-2024-00397336). The authors would like to thank Y-TECH for their support in the fabrication of the LTCC module.
Fig. 1
Schematic of the proposed CMOS detector.
Fig. 2
(a) Circuit simulation results of the detector output for different inductances, and (b) EM simulation results of inductance and SRF variations versus the inductor length.
Fig. 3
(a) Die photograph of the proposed CMOS detector fabricated using a 40-nm bulk CMOS process and (b) its LTCC module implementation.
Fig. 4
Measured voltage responsivity and noise-equivalent power of the proposed CMOS detector at 120 GHz as a function of gate bias.
Table 1
Performance comparison of the proposed CMOS detector in sub-THz frequencies
|
Ref. |
Process (nm) |
fc (GHz) |
RV (kV/W) |
NEP (pW/Hz)
|
Core area (mm2) |
|
[4] |
22 (SOI) |
400 |
0.012 |
115 |
1.26a
|
|
[5] |
65 |
300 |
1.49 |
6.5 |
0.076 |
|
[6] |
250 |
200 |
14,130b
|
34.4b
|
0.556a
|
|
[7] |
40 |
309 |
40 |
62.5 |
0.016 |
|
This work |
40 |
120 |
1,247b
|
1.6b
|
0.075 |
References
1. J. Hu, C. Zhan, H. Shi, P. Qiao, Y. He, and Y. Liu, "Rapid non-destructive detection of foreign bodies in fish based on terahertz imaging and spectroscopy,"
Infrared Physics & Technology, vol. 131, article no. 104448, 2023.
https://doi.org/10.1016/j.infrared.2022.104448
2. T. T. Nguyen, D. H. Kim, J. H. Choi, and C. W. Jung, "Circularly polarized series array and MIMO application for sub-millimeter wave/terahertz band,"
Journal of Electromagnetic Engineering and Science, vol. 24, no. 3, pp. 294–304, 2024.
https://doi.org/10.26866/jees.2024.3.r.230
3. F. Lu, L. Yao, C. Liu, J. Ling, and H. Deng, "Optical performance enhancement of a blocked-impurity-band photodetector integrated with terahertz metalenes,"
Materials Science and Engineering: B, vol. 314, article no. 118010, 2025.
https://doi.org/10.1016/j.mseb.2025.118010
4. M. Hoogelander, S. van Berkel, E. S. Malotaux, M. Alonso-delPino, D. Cavallo, M. Spirito, and N. Llombart, "Chessboard focal plane array for a CMOS-integrated terahertz camera,"
IEEE Transactions on Terahertz Science and Technology, vol. 13, no. 6, pp. 704–717, 2023.
https://doi.org/10.1109/TTHZ.2023.3297072
5. Y. Wang, T.-Y. Chiu, T.-Y. Chiu, K.-J. Yu, Y.-M. Teng, G.-W. Huang et al., "A Ka- to G-band detector with 5.5-GHz video bandwidth using a modified traveling-wave structure in 65-nm CMOS Technology,"
IEEE Transactions on Circuits and Systems II: Express Briefs, vol. 70, no. 4, pp. 1371–1375, 2023.
https://doi.org/10.1109/TCSII.2022.3227469
6. M.-J. Lee, H.-N. Lee, G.-E. Lee, S.-T. Han, and J.-R. Yang, "Concurrent-mode CMOS detector IC for sub-terahertz imaging system,"
Sensors, vol. 22, no. 5, article no. 1753, 2022.
https://doi.org/10.3390/s22051753
7. L. J. Xu, Z.-J. Xie, X. Bai, Q. Li, B.-K. Wang, and P.-C. Yin, "Design of THz monolithic source and detector in 40-nm CMOS,"
Journal of Infrared, Millimeter, and Terahertz Waves, vol. 42, no. 9, pp. 1040–1060, 2021.
https://doi.org/10.1007/s10762-021-00787-6